PDF disclaimer. This PDF file may contain embedded typefaces. In accordance with Adobe’s licensing policy, this file may be printed or viewed. Flang 6A Flange_ABF. DN. Zoll size mm. FLANGE. A. B. F. 16A 1/2. 1/2. 16A 1/2. 3/4. STANDARD. ISO. Second edition. Reference number. ISO (E). This is a free 6 page sample. Access the full version online.
|Published (Last):||7 March 2009|
|PDF File Size:||8.47 Mb|
|ePub File Size:||19.73 Mb|
|Price:||Free* [*Free Regsitration Required]|
A list of organizations represented on this subcommittee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.
Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii to v, a blank page, pages 1 to 18, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd.
Date Comments Li ce ns ed C op y: In the kilnuley evtne ttah isp borpmel talerign to ti f si,dnuo isoo eorm teh tneCS laretercratai ta thserdda es igvne olebw. The work of preparing International Standards is normally carried out through ISO technical committees.
Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Attention is drawn to the possibility that some of the elements of this part of ISO may isl the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO consists of the following parts, under the general title Hydraulic fluid power — Flange connectors with split or one-piece flange iiso and metric or inch screws: Components are interconnected through their ports and associated fluid conductor connector ends.
BS ISO 6162-2:2018
Also, the tube ios and wall thickness depend on the selected working pressure and tube diameter. Tube dimensions shall be calculated in accordance with ISO It also specifies the dimensions of the seals to be used, as well as the grooves to house the seal. This part of ISO also recognizes the need to accommodate metric type 1 screw fasteners, isso well as to provide a means to use existing inch type 2 screw fasteners.
These connectors are intended for application in hydraulic systems on industrial and commercial products, where it is desired to avoid the use of threaded connectors.
STAUFF: SAE Split Flange Halves and SAE Flange Clamps
Surges of pressure higher than the nominal ratings will reduce the ability of the izo connectors to retain the hydraulic fluid. This should be taken into account in the design of the hydraulic system. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply.
However, parties to agreements based on this part of ISO are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Tolerances for 61662-2 and 61622-2 dimensions without individual tolerance indications ISOFluid 662-2 systems — O-rings — Part 1: Inside diameters, cross-sections, tolerances and size identification code ISOFluid power systems — O-rings — Part 3: The O-rings shall conform to the dimensions given in Table 4 and shall meet or exceed the O-ring quality acceptance criteria for grade N of ISO NOTE For higher temperatures, use sealing materials that meet the higher requirements.
Table 1 lists pressures and torques when property class 8.
These screws should be used for severe vibration applications, e. Table 2 lists pressures and torques when property class In this case, the surface pressure on the screw head and between flange clamp and flange head shall be considered. Hardened flat washers may be used. NOTE The flange head selection is not affected by the difference in metric or inch screw fasteners.
NOTE Dimensions and tolerances given in the tables apply to the finished parts, plated or otherwise processed, as specified by the purchaser.
Weld-on flange heads shall be protected from corrosion uso an oil film, phosphate coating or by other means that do not negatively affect weldability to meet a neutral salt spray test in accordance with ISOunless otherwise agreed upon by the supplier and purchaser.
All screws of property class All machined surfaces shall have a surface roughness value ofexcept where otherwise specified. Annular tool marks up to a surface roughness value,uso shall be permitted. Burst and cyclic endurance tests shall be conducted on flange connections. Such connectors shall be suitable for use in hydraulic systems at ambient temperatures from to. NOTE The temperature range of connectors with elastomeric seals depends on the limits of the temperature range of the seal.
Working pressure for connectors made from stainless steel and used at elevated temperatures shall be reduced aboveabove and above. Letter height shall be minimum. Location of the marking may differ from the location shown in Figure 3. Marking shall be on the top side or outside of the flange.
No identification is required for type 2 clamp halves or for one-piece flange clamps. No identification is required for type 2 ports. Split flange 61162-2 port assembly, metric series including screws and O-ring: Use of other materials may require different screw lengths.
Net tightening torque depends on many factors, including lubrication, coating and surface finish. These dimensions do not apply when more than one size 6612-2 flanges are used on adjacent ports. For equivalent inch O-rings, see annex A. SAE J does not provide an equivalent material specification for inch screws.
It presents the UK view on standards in Europe and at the international level. It is incorporated iwo Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services.
We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical 61662-2 responsible, the identity of which can be found on the inside front cover.
BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.
SAE Split Flange Halves and SAE Flange Clamps
Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Standards are also available from the BSI website at http: In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service.
Various BSI electronic information services are also available which give details on all its products and iiso. Contact the Information Centre.
APSOparts – Semi flange for SAE-fitting S6 PSI ISO , 35
Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Information regarding online access to British Standards via British Standards Online can be found at http: Copyright Copyright subsists in all BSI publications.
BSI also holds the copyright, in the UK, of the publications of the international standardization bodies.
Except as permitted under the Copyright, Designs and Patents Act no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means — electronic, photocopying, recording or otherwise — without prior written permission from BSI.
This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, 6162-22 size, type or grade designations. If these details are to be used for any other purpose than 61622 then the prior written permission of BSI must be obtained. ISO Hexagon flange head tapping screws. BS EN Flanges and their joints – Gaskets for class-designated flanges – Covered serrated metal gaskets for use with steel flanges.