6(&. iC-v SERVICE. MANUAL DISASSEMBLY INSTRUCTIONS. SECTION 4 . Specified Icom’s battery pack only (Operating voltage range; – V). View and Download Icom IC-V82 instruction manual online. Icom America VHF Transceiver, VHF Transceiver Instructions Manual. IC-V82 Transceiver pdf. View and Download Icom IC-V82 instruction manual online. VHF TRANSCEIVER . IC-V82 Transceiver pdf manual download.
|Published (Last):||11 September 2017|
|PDF File Size:||19.66 Mb|
|ePub File Size:||9.42 Mb|
|Price:||Free* [*Free Regsitration Required]|
This device complies with Part 15 of the FCC rules. Operation is sub- ject to the following two conditions: BPN will become exhausted. To provide the recipients of your Direct frequency input from the key- pad is also available. Setting frequency In VFO mode, set the desired operating frequency with other desired settings, such as repeater and subaudible tone.
Attach the belt icpm with the supplied screws using a phillips screwdriver. To attach the belt clip D Handstrap Not supplied Slide the hand strap through the loop on the top of the rear panel as maanual below.
SCAN channel selection, etc. Only tested and approved for use with genuine Icom bat- teries. The following are additionally required: The following items are additionally required. VFO mode and icc-v82 mode.
ICOM IC-V82 INSTRUCTION MANUAL Pdf Download.
See next set of instructions for setting tuning step size. The display type is selected in p. When the reversed duplex mode is selected, the ico, fre- quency shifts. Transmit frequency shifts in normal duplex mode. Each receive and transmit frequency is shown in the table below with the following conditions; IC-V82 Input frequency: D D Tone information Some repeaters require different tone ic-v28 to be accessed. The offset amnual repeater tone frequencies are not changed by the auto repeater function.
Each of these channels can be individually programmed with op- erating frequency pgs. Each mem- ory channel, 0 tomay be assigned to one of the banks for easy memory management.
Even if the memory bank contents icomm cleared, the memory channel contents still remain pro- grammed. DTMF memories are used to store phone numbers or control codes. Program them in the same manner as regular memory channels. D Memory scan watch While operating on a VFO frequency, memory scan watch monitors for signals in each memory channel in sequence, every 5 sec.
You can wait for calls from group members using the same tone and not hear other signals. D Setting subaudible tones for tone squelch operation Separate tone frequencies can be select for tone squelch op- mnual rather than repeater operation the same range of tones is available— see right below.
Pager selective code push [PTT] Answer back manual Set both transceivers to either code squelch or non-coded operation Up to 6 transmit codes codes that you transmit are pro- grammable into code channels, C1 to C6, if required.
D D Your call sign note programming You can add information to your own call sign such as kcom ating radio type or area. Call sign notes are coupled with the same channel number of your own call signs, and they are transmitted or indicated after your own call signs. In the EMR communication mode, no call sign set- ting is necessary.
The digital code or call sign squelch does not function while in a low- speed ic-v28 communication. Iom system provides you with much wider coverage range during digital voice mode operation. D D Auto Rx call sign Display When an individual station call is received, the calling station call sign can be indicated automatically.
When this setting is set to ON, the transceiver automatically indicates your programmed call sign at turning power ON or digital mode transmission.
The GPS message is transmitted from Tx message channels. The position data can also be transmitted with a message to another station.
Icom IC-V82 Instruction Manual
Total of codes are available. When receiving signals, the scan pauses according to the scan pause time. This setting can be set for each memory, call and VFO inde- pendently. The offset and repeater tone is not changed by the auto repeater function.
Reset these frequencies, if necessary. The auto repeater function is turned OFF. Duty cycle changes automatically. Microphone simple mode is used to change the function as- signments for keys in the optional HMA as below.
This setting allows you to set a kanual signal level needs to open the squelch. The previously selected used weather channel is checked periodically during standby or while scan- ning. This may be caused externally by static electricity or by other factors. If this problem occurs, turn power OFF.
After waiting a few seconds, turn power ON again. Cloning allows you to quickly and easily transfer the pro- grammed contents from one transceiver to another trans- ceiver. Insert the connector firmly to avoid a bad contact. Transmit at 7 W High at 4 W Middle 2.
Transmit at 5 W High at 2 W Middle 1. Some options may not be available in some countries. Please ask your dealer for details. When the display type setting pgs. Page of 96 Go. Table of Contents Add to my manuals Add.
Repeater Operation Direct frequency input from the key- pad is also available. Repeater Operation When the reversed duplex mode is selected, the receive fre- quency shifts.
Scan Resume Condition D Memory scan watch While operating on a VFO frequency, memory scan watch monitors for signals in each memory channel in sequence, every 5 sec.
Page 47 D Setting subaudible tones for tone squelch operation I-cv82 tone frequencies can be select for icoj squelch op- eration rather than repeater operation the same range of tones is available— see right below. Code Squelch [PTT] to receive. Page 55 D D Your call sign note programming You can add information to your own call sign such as oper- ic–v82 radio type or area. Page 67 D D Auto Rx call sign Display When an individual station call is received, the calling station call sign can be indicated automatically.
Ic-f82 Cloning allows you to quickly and easily transfer the pro- grammed contents from one transceiver to another trans- ceiver. Page 94 We Icom Inc. Page 95 We Icom Inc.
This manual also for: Comments to this Manuals Your Name. Enter text from picture: By pressing ‘print’ button you will print only mannual page. To print the manual completely, please, download it.
Don’t show me this message again. Got it, continue to print. Don’t have an account?