EASYGEN 3200 MANUAL PDF

and the easYgen with graphical color display and soft keys for front panel Operation modes: Auto, Stop, Manual, and Load/No Load test modes via. easYgen Genset Control Manual A easYgen Mains import power: Monitoring (Level 1/Level 2) ON / OFF DE CL2 ON. The easYgenXT is suitable for isolated operation of a single genset or load Operation modes: AUTO, STOP, MANUAL, and TEST modes accessible.

Author: Mezigar Dira
Country: Philippines
Language: English (Spanish)
Genre: Relationship
Published (Last): 2 February 2018
Pages: 344
PDF File Size: 18.17 Mb
ePub File Size: 10.12 Mb
ISBN: 927-2-57344-888-2
Downloads: 7905
Price: Free* [*Free Regsitration Required]
Uploader: Malak

Provides other helpful information that does not fall under the warning or caution categories. Woodward reserves the right to update any portion maual this publication at any time. Information provided by Woodward is believed to be correct and reliable. However, Woodward assumes no 33200 unless otherwise expressly undertaken. Figures and Tables Figures Figure Housing – panel-board cutout Housing easYgen – dimensions Housing – drill plan Wiring diagram — overview Housing – panel cutout Conversion chart – wire size Power supply – terminal assignment Voltage measuring FlexRange – terminal assignment – generator voltage Manual – overview Intended Use The unit must only be operated in the manner described by this manual.

Panel cut-out Cut out the panel according to the dimensions in Table Don’t drill the holes if you want to use the clamp fasteners. If the holes are drilled into the panel, the clamp fasteners cannot be used anymore! In order to enhance the protection to IP 66, it is possible to fasten the unit with a screw kit instead of the clamp fastener hardware. Wiring Diagrams [refer to next page for wiring diagram] Figure Only the values indicated in Chapter 6: Technical Data on page 47 are valid!

  LEY 19281 PDF

Woodward easYgen-3000 Installation Manual

Power supply – crank waveform at maximum load NOTE Woodward recommends to use one of the following slow-acting protective devices in the supply line to terminal DO NOT use both sets of voltage measuring inputs. The control unit will not measure voltage correctly if the V and V inputs are utilized simultaneously.

NOTE Woodward recommends protecting the voltage measuring inputs with slow-acting fuses rated for 2 to 6 A. Please note to configure and wire the easYgen consistently. Refer to the Configuration Manual for more infor- mation.

Voltage measuring FlexRange – busbar system 1 1Ph 2W phase-phase.

Connection of the transducers. Manual A easYgen Series – Genset Control Ground Current The mains current input can be configured to measure the mains current or ground current. Depending on how Parameter ‘Input mains current as’ is configured will determine if this input will measure the mains current de- fault or the ground current.

Signal Polarity The discrete inputs are electrically isolated which permits the polarity of the connections to be either positive or negative.

NOTE All discrete inputs must use the same polarity, either positive or negative signals, due to the common ground. Operation Logic Discrete inputs may be configured to normally open N. In the state N. Relay outputs Terminal Description Term.

Type Form A, N. The specified accuracy of 2. It is possible to combine single- and two-pole senders. Analog controller output – Wiring and external jumper setting RS interface 1 – overview Terminal Description not connected not connected not connected not connected not connected Manual A easYgen Series – Genset Control Discrete inputs isolated Input range V Manual A easYgen Series – Genset Control Interface RS interface RS Standard Signal level Environmental Data Vibration Frequency Range — Sine Sweep If your serial or CAN bus cable is equipped with a housing, which does not fit into the easYgen socket, you may replace the housing with Page of 54 Go.

  CONVITE A FILOSOFIA MARILENA CHAUI PDF

Page 21 – Figure Page 22 – Figure Page 23 – Voltage Measuring: Mains Page 24 – Figure Page 25 – Figure Page 26 – Figure Page 27 – Voltage Measuring: Busbar System 1 1Ph Page 28 – Figure Page 29 – Current Measuring Page 30 – Figure Current measuring – generat Page 38 – Discrete Inputs: Page 46 – Figure Interfaces – CAN bus – term Table of Contents Add to my manuals Add.

Page 2 Provides other helpful information that does not fall under the warning or caution categories. Page 5 Figures and Tables Figures Figure Power Supply [ms] Figure Page 48 Manual A easYgen Series – Genset Control Discrete inputs isolated Input range V Page 49 Manual A easYgen Series – Genset Control Interface RS interface Comments to this Manuals Your Name. Enter text from picture: Hi i need to download this manual.

By pressing ‘print’ button you will print only current page.

easYgen XT / XT

To print the manual completely, please, download it. Don’t show me this message again.

Got it, continue to print. Don’t have an account?